Well, it must still be under some type of warranty program. Assuntos variados 2 13.995 visualizaciones 6:34 Floppy Disk(s) Fail (40) resuelto - Duración: 2:18. Stand up for your rights!!! If you have any additional recommendations for Marlene, let's hear them! http://casualobserver.net/floppy-disk/floppy-disk-s-fail-40-error-but-i-don-t-have-a-floppy-drive.html
please help. right if that's the case then you have to make sure that the device is disabled in the BIOS. I do not know how to get into the BIOS on XP. You can select the Cable selection or remove all jumpers.3.
Report luko- Apr 2, 2009 at 06:36 AM how do I do that? I have seen quite a few problems with the ide 40 pin connectors and I guess the new SATA cables and their fragile looking connectors are almost begging to cause trouble. If the floppy drive is not setup properly you may experience read/write errors or the floppy may not work at all. Report tuvshuuu- May 23, 2010 at 05:00 AM you saved me thanks a lot, god bless you.
Typically this is a menu system accessed by pressing a certain key on the keyboard when the PC starts....Tom's Hardware: BIOS for Beginners http://www.tomshardw...nners,1126.htmlMost PCs briefly display a message describing how Is it a key on the keyboard? Alsmo make sure that the data cable is inserted properly into the motherboard. Floppy Disk Fail 40 Windows 7 Do I need a boot disk or a full system restart?
Thank you. If I shut the PC down and restart it, everything appears to run OK. If this persists disconnect (permanently) the floppy drive from the PC. http://www.geekstogo.com/forum/topic/40166-floppy-disks-fail-40-problem-resolved/ I followed your steps and it worked accuratedly.
change it to none. Floppy Disk Failure When the PC starts up, the first job for the BIOS is to initialize and identify system devices such as the video display card, keyboard and mouse, hard disk, CD/DVD drive Invalid drive specification - Verify that you floppy drive is setup properly in CMOS Setup. Iniciar sesión 22 Cargando...
Thanks a ton man. https://www.cnet.com/forums/discussions/disk-boot-failure-what-is-it-and-what-can-i-do-to-resolve-it-257993/ All rights reserved. Floppy Disk Fail 40 Solution Reproducción automática Si la reproducción automática está habilitada, se reproducirá automáticamente un vídeo a continuación. Floppy Disk(s) Fail (40) Windows 7 BenP Port Moresby Papua New Guinea Report Thaulsa- Aug 2, 2009 at 02:08 PM thank you very much rapture I had problems with my diskette not working so I pulled the
This explained the issue. this content Before you get much invested in it, in terms of work and files and such, it's best to get that drive replaced and re-imaged.If there's no warrantee, replacement hard-drives are relatively If it's still crashing it could be a hardware fault. They asked me to purchase at recovery disk, and I said taht i'll need to thik about it so they're calling me tomorrow on april 21st around 9-10 pm eastern. Floppy Disk Fail 40 Windows 10
Inicia sesión para añadir este vídeo a una lista de reproducción. Keep me posted if possible.http://forums.cnet.com/5208-10149_102-0.html?forumID=7&threadID=257993&messageID=2552073#2552073Submitted by: H41N Please see below for additional advice from our members. Please help. weblink Thankfully the tech could hear the frustration in my voice and I told him thousands of people on the internet wrote with this same problem so this is prevalent to DELL
Since it seems that your computer is new, I assume that's the operating system. Floppy Disk S Fail 40 Error On Bootup Report BenP- Jul 27, 2009 at 09:15 PM Thanks very much for all your wonderful notes on how to solve this problem. if these don't work refer to this post and I will try and help you on your problem, but post your hard drive configuration and maybe some pictures of your bios
Email Id removed for security. After trying everything. Thanks so much. How To Fix Floppy Disk Fail 40 Windows 7 Select the Windows installation drive, which is usually C:\, and click Next Choose Command Prompt when the System Recovery Options box appears Write the following command and press Enter afterwards: chkdsk
IF it fails to enter BIOS remove power cable from hard drive and then try entering BIOS again, it should work. (off course before removing power from hard drive shut down I havent got floppy, and i had disable flopy in/on?? thanks tons. http://casualobserver.net/floppy-disk/floppy-disk-error-40.html Flag Permalink This was helpful (0) Collapse - RE:-> by Thomasskins / August 5, 2007 4:02 AM PDT In reply to: Disk Boot failure Hi, i'm new to PC & get
Report Postal268- Mar 20, 2009 at 08:24 AM Dude thank you so much, I had been messing with the setup for hours. Description and Symptoms The error messages, alerts, warnings, and symptoms below are tied to this error. I do all of this and my dell inspiron 530 is start normally thank you again Report faysal_2011- Nov 12, 2012 at 06:00 AM thank you TO DISABLE FDC CONTROLLER.... for dell users u have change your first boot hardware to Harddisk and the go to integrated components and disable FDC.
Replace the following hardware in the computer in the below order. Sincerely Computernovice. Some facilities may be able to salvage information off your original disk for transfer (although where you are still at a point where your OS boots occasionaly, backing up data important I'm pretty good with computers, but I don't want to do it wrong, so if you could walk me through the steps pls..
If the problem persists, replace the diskette/CD-drive subsystem. Report doeboy- Oct 6, 2009 at 06:22 PM went through the bios and didnt c anything that said , standard cmos, im pretty good with pcs and iv seen that b4 You're allowed only a few moments to press the required key before your operating system starts to load. A 'disk boot failure' error message could just be that the bios is looking at the wronge drive!
When this happens the computer may or may not startup. I have been looking at this error message and wondering what it meant for ages. Arrow down to select "Integrated peripherals" - press enter; Arrow down to select "Onboard FDC controller" - press enter; Arrow cursor to select "disabled" - press enter; Press F10 to save