Repair Floppy Drive Problem Tutorial Home > Floppy Disk > Floppy Drive Problem

Floppy Drive Problem


The error messages described in Table 3.1 are errors that occur and are reported before the single beep tone is produced at the end of the POST routines. The disadvantage is that these cables are hard to find. Privacy Policy | Cookies | Ad Choice | Terms of Use | Mobile User Agreement A ZDNet site | Visit other CBS Interactive sites: Select SiteCBS CaresCBS FilmsCBS RadioCBS.comCBS InteractiveCBSNews.comCBSSports.comChowhoundClickerCNETCollege NetworkGameSpotLast.fmMaxPrepsMetacritic.comMoneywatchmySimonRadio.comSearch.comShopper.comShowtimeTech There’s really nothing that can be done from a user’s perspective to repair a dead motor or an electrical problem with the floppy drive’s circuit board.

See our floppy disk and floppy drive definitions for further information on each of these terms. By following the steps in those articles, you should be able to identify where the problem lies. Hardware needed: Serial port on both ends Software needed: If using DR DOS or MSDOS 6.x, the software should already included (in MSDOS, it's called INTERLNK.EXE and INTERSVR.EXE). It may be faster to repair the drive than to drive all the way to the store and buy a new one.In my next article, I’ll share several techniques for repairing

Floppy Disk Problems And Solutions

Bought external drive unit! Once at the prompt, place a diskette into the floppy disk drive and type format a: if you get: Invalid media or Track 0 Bad - Try formatting another floppy disk. You can try, but you'll quickly destroy both disk and drive in the process, in addition to making a complete fool out of yourself. Autoplay When autoplay is enabled, a suggested video will automatically play next.

The best way I've found to do this is through an excellent utility that writes the floppy boot sector for you called Boot_B, which is in the Resouces section at the Most computers need to have the floppy setup as a 3.5, 1.44MB. Floppy drive refuses to read diskettes Help! The Disk Media Is Not Recognized Floppy Those Paranoid Software Companies Those silly programmers!

What is more likely is that you forgot to connect the power cable to the drive. Floppy Disk Drive Problems If connected, disconnect, and then connect the floppy drive cable to verify seated properly. in question. If the disk appears to format correctly and reports 1213952 bytes available on disk, you're done!

If your floppy cable has more than one connection, verify that you have connected the floppy to the appropriate connection. Floppy Disk Format Error Floppy drives tend to accumulate an amazing amount of dust.If after removing the dust, the drive still doesn’t want to read or write, I recommend unplugging the computer and removing the Contact us to obtain licensing.Use of this site is subject to certain Terms of use which constitute a legal agreement between you and Acme, Inc. Check the connection to the drive and to the motherboard.

Floppy Disk Drive Problems

If the floppy drive's LED is always on, the data cable may be reversed. In this article, I’ll walk you through some common floppy drive service and repair methods.More floppy drive resources If you've missed any of Brien Posey's previous articles on troubleshooting floppy drives, Floppy Disk Problems And Solutions Zagroseckt 8,672 views 7:04 Floppy to USB reader: Troubleshooting video - Duration: 6:03. How To Read A Floppy Disk Without Formatting It Verify that a power connection is also connected to the back of the floppy drive.

Not setup in CMOS Verify that the floppy drive is properly setup in CMOS Setup. this content When it becomes necessary to replace the CMOS backup battery on the system board. Verify that the diskette is not write protected by sliding the tab into the position not allowing light to shine through it. Write Protect Error - Ensure that the disk is not write protected by removing the floppy disk and insuring that you cannot see through both holes; if you can, move the Floppy Drive Not Working

YesNo Feedback E-mail Share Print Search Recently added pages View all recent updates Useful links About Computer Hope Site Map Forum Contact Us How to Help Top 10 pages Follow us It's a high density disk drive. RetroGamerVX 11,437 views 12:10 Quick Fix Floppy Disc cleaning / read error's / - Duration: 7:04. weblink Crap.

RetroGameModz 12,259 views 25:30 Amiga 1200 repair - Video problem - Duration: 25:07. Floppy Disk Not Recognized Next, use a cotton swab with alcohol to clean the drive heads. Sign in to add this video to a playlist.

You must decide whether to repair or replace the floppy drive.Replace vs.

Write Protect Error - Ensure that the disk is not write protected by removing the floppy disk and insuring that you cannot see through both holes; if you can, move the These sources are summarized in the following list that includes the typical error messages associated with each source. Sign in Transcript Statistics Add translations 5,239 views 61 Like this video? Floppy Disk Driver Windows 7 Replace or request that the motherboard \ I/O board be replaced.

If you are running Windows 3.x click File and click Exit Windows to get to an MS-DOS prompt. I have a local mirror of it that I will be putting on at some point, but until then consult this list of cracks/patches for old games: A mirror of Yes, bubblegum and shoestring networking at its best. Bad hardware If you continue to experience issues after following the above steps it is likely that hardware within the computer is bad.

Verify that the floppy connection is connected to the motherboard FDD connector.