You may have a problem with the floppy disk controller. Other components may also cause these same symptoms, check the general diagnosis page for more information. replacing a dead drive.Try a known-good floppy driveTo determine whether your problem involves the disk drive or the disk controller, locate another PC whose floppy drive works properly. Please consider a donation to The PC Guide Tip Jar. his comment is here
Problem with Floppy Drive More resources Tom's Hardware Around the World Tom's Hardware Around the World Denmark Norway Finland Russia France Turkey Germany UK Italy USA Subscribe to Tom's Hardware Search As for finding one, I just went to Price Watch and poked around until I found one on Aberdeen's online catalog (one of the vendors who subscribe to Price Watch's service). Did those software companies think that handfulls of teenagers wouldn't be able to figure out how they were doing it? Let's continue...
If you encounter configuration (or setup) errors, refer to the installation instructions found in the new component's installation/user documentation. These sources are summarized in the following list that includes the typical error messages associated with each source. It's a high density disk drive.
If you've got a game that is hard-wired to do this, accessing unit 0 directly, you have no choice but to swap the controller cables to make the 5.25" drive the Well, boys and girls, you'll have to get your hands on a real live 5.25" floppy drive to get around that. If the boot sequence starts with the letter of a hard disk drive (like C:), and that drive is having a problem, the system will never even attempt to boot from Floppy Disk Format Error If you don't know what the density of your blank disks are, try to find blank disks without a hub ring (that little circular "hoop sticker" at the center of the
Since the pinout is sometimes different from cable to cable, and since I only have one and don't want to damage it, I don't have a pinout for you. Floppy Disk Not Recognized If you’re lucky enough to get your hands on such a card, disable your onboard disk controller (usually through the CMOS, but possibly with a jumper), and connect the floppy drive All rights reserved. Hardware needed: Parallel port on both ends.
Learn how to determine whether the drive controller or the drive itself is bad. It's possible to create a boot sector on a floppy disk in drive A: that redirects the boot process over to drive B:, swapping all the BIOS drive references along the Floppy Disk Problems And Solutions Kozierok.All Rights Reserved. The Disk Media Is Not Recognized Floppy Invalid drive specification - Verify that you floppy drive is setup properly in CMOS Setup.
Swapping Cables Copy-protection is ugly because software piracy is ugly. this content Which is, unfortunately, the only thing about old software that you can't tweak or customize into shape without opening the hood. Alternatively, you can try to find an old copy of LapLink, FastLynx, or Norton Commander for an elegant solution. Before you open up the hood again to start swapping cables around, there's a little-known solution that works with all games that are only mildly copy-protected (they use the BIOS to Floppy Drive Not Working
In these cases, the user must manually resolve the configuration problem. With the proliferation of CDs, CD-Rs, CD-RWs, Zip drives, SuperDisks, and recordable DVDs, is the 3.5-inch floppy obsolete? While this is not a hard and fast rule, about 95% of all the unlabeled disks you find without a hub ring will be high density disks. http://casualobserver.net/floppy-disk/floppy-disk-s-fail-40-error-but-i-don-t-have-a-floppy-drive.html You start by saying "NOT XP" - What are you saying here ?Why are you going to A: drive when your Floppy drive was assigned O:You must have had a problem
Floppy drive refuses to read diskettes solved USB floppy drive not reading solved where can i find a full version of MS-DOS on your floppy drive? Floppy Disk Driver Windows 7 Installing a floppy drive is also easier than you think. If the opposite happens then your drive is either bad or misjumpered.
The drive is out of alignment. "Sector not found" error The drive is out of alignment. The floppy drive may need to be replaced. "Drive not ready" error There is no disk in the floppy drive. However, I have been able to find PCI cards or ISA cards with disk controllers built into them. Enabling Devices And Changing The Boot Order Are Settings Of What? Also, don't assume where pin 1 is on the drive, since this tends to vary with different hardware.
Bad hardware If you continue to experience issues after following the above steps it is likely that hardware within the computer is bad. These drives are large and I have seen problems like cables hanging down into the mechanics of the drive and impeding its operation. Skip to Main Content Search Help Tips Dictionary History Forums Contact You are here: Help > Hardware Help > Floppy Drive Help Basic floppy disk drive troubleshooting Note: This document is check over here The operating system side of the system does not come into play until after the beep occurs.
well, you just don't want to take any chances with copy-protection.