How To Repair Floppy Not Connected (Solved) Home > Floppy Disk > Floppy Not Connected

Floppy Not Connected

Contents

Was this page useful? If you are running Windows 95, Windows 98, Windows ME, Windows NT, Windows 2000, or Windows 2000 click Start, Shutdown, and Restart the computer to an MS-DOS prompt. By bumping on someone's topic it makes it confusing for the tech to understand who they are helping. Show Ignored Content As Seen On Welcome to Tech Support Guy! his comment is here

If the floppy drive is usable after booting the hard disk but just will not boot, look here.

Diagnosis: There are many different causes of apparent floppy drive failures. Bad floppy disketteVerify that the floppy diskette that you are attempting to read from is not write protected or bad. I've connected the large wire to the mother board and I see there's the led switch on, telling me that the floppy is on. Are you looking for the solution to your computer problem? http://www.computerhope.com/issues/ch000277.htm

Floppy Disk Problems And Solutions

Advertisement number Thread Starter Joined: Oct 15, 2003 Messages: 1,045 another problem, the floppy disk doesn't read anything. Replace the following hardware in the computer in the below order. Reverse the connector.

Was this page useful? If the disk is not write protected try another floppy disk. If you continue to experience the same issues we recommend that Windows be reinstalled. Floppy Disk Drive Problems Now, this site will take you days to get through, but it is the most accurate, comprehensive guide around....

If you're new to Tech Support Guy, we highly recommend that you visit our Guide for New Members. How To Read A Floppy Disk Without Formatting It If you are just installing this floppy drive, make sure you don't have the cable connected backwards. Floppy drives are very simple affairs and outright failure is quite rare--even in old drives. http://www.computerhope.com/issues/ch000343.htm Create Account How it Works Javascript Disabled Detected You currently have javascript disabled.

Most computers need to have the floppy setup as a 3.5, 1.44MB. Floppy Disk Format Error Find The PC Guide helpful? You're allowed only a few moments to press the required key before your operating system starts to load. Verify that the floppy cable coming from the motherboard is connected to the back of the floppy drive.

How To Read A Floppy Disk Without Formatting It

The BIOS software is specifically designed to work with the particular type of system in question, including having a knowledge of the workings of various devices that make up the complementary https://kb.vmware.com/kb/1034616 Once registered and logged in, you will be able to create topics, post replies to existing threads, give reputation to your fellow members, get your own private messenger, post status updates, Floppy Disk Problems And Solutions YesNo Feedback E-mail Share Print Search Recently added pages View all recent updates Useful links About Computer Hope Site Map Forum Contact Us How to Help Top 10 pages Follow us Floppy Drive Not Working This procedure does not deal with the physical installation of the drive; for instructions on installing the drive, refer to this procedure.

You see a red stripe on one edge of the ribbon- that red side must correspond to pin1 for the motherboard port (also called channel, connector) The pin1 side may be this content Not responsible for any loss resulting from the use of this site. Covers ALL aspects of hardware, BIOS etc, and I mean ALL! Sign In Use Facebook Use Twitter Use Windows Live Register now! The Disk Media Is Not Recognized Floppy

not the driver there is no actual place to put floppy disks in. I have same probleme. It is easy with many 3.5" drives to connect the drive backwards because the cable is keyed but the connectors aren't always. http://casualobserver.net/floppy-disk/floppy-disk-s-fail-40-error-but-i-don-t-have-a-floppy-drive.html This means that it is possible to connect the cable upside-down, and then of course the drive will not work.

Bad hardware If you continue to experience issues after following the above steps it is likely that hardware within the computer is bad. Floppy Disk Not Recognized Join over 733,556 other people just like you! See our floppy disk and floppy drive definitions for further information on each of these terms.

Each one can be different, but each should have a manual.

Yes, I know there is no floppy drive, but message is your motherboard telling you that it is not there....somehow, (did you perhaps hit default settings or flash your bios), floppy managed replied Feb 9, 2017 at 10:44 PM Help AMD processor LIS333 replied Feb 9, 2017 at 10:40 PM Can add files to microSD card... :z: replied Feb 9, 2017 at Username or email: I've forgotten my password Forum Password Remember me This is not recommended for shared computers Sign in anonymously Don't add me to the active users list Community Forum Floppy Disk Driver Windows 7 If the drive's activity light comes on as soon as the PC is booted and stays on, solid the whole time the PC is on, this is a dead ringer for

Custom Search Toggle navigation Home Create Find and Join Admin Login Help About FAQ Docs Privacy Policy Contact Us [foxboro] floppy disk drive not connected error From: "Currano, Joe" If it appears to be connected, disconnect, and then reconnect cable to verify cable is seated properly. Because of the technology of floppy diskette drives, it is likely for a floppy diskettes to become bad. check over here Verify that the floppy connection is connected to the motherboard FDD connector.

Please read the Site Guide before using this material. If other floppies work it is likely that you may have a bad floppy diskette. Typically this is a menu system accessed by pressing a certain key on the keyboard when the PC starts....Tom's Hardware: BIOS for Beginners http://www.tomshardw...nners,1126.htmlMost PCs briefly display a message describing how Choosing the wrong type of drives can cause a failure to be reported.

Additional information Unable to read floppy diskette. Replace the following hardware in the computer in the below order. Windows 9x not detecting floppy properly If the floppy drive is working, verify that Windows is detecting the floppy drive properly by verifying no conflicts are present in Windows Device Manager. This site is completely free -- paid for by advertisers and donations.

Adapters are available for a couple of bucks for use in older systems. Edited by andrewasmith1, 28 June 2005 - 01:23 PM. 0 Advertisements #2 samiko Posted 28 June 2005 - 12:54 PM samiko Retired Staff Retired Staff 424 posts open your machine case, If connected, disconnect, and then connect the floppy drive cable to verify seated properly. If conflicts are present, resolve those conflicts before referring to the next paragraph.

If the opposite happens then your drive is either bad or misjumpered. The errors are: FLOPPY DISKS FAIL 40 KEYBOARD ERRORS OR NO KEYBOARD PRESENT CMOS CHEKSUM ERROR - DEFAULTS LOADED I take out the BIOS battery, I unplug and plug again the Once at the prompt, place a diskette into the floppy disk drive and type format a: if you get: Invalid media or Track 0 Bad - Try formatting another floppy disk. Skip to Main Content Search Help Tips Dictionary History Forums Contact You are here: Help > Hardware Help > Floppy Drive Help Basic floppy disk drive troubleshooting Note: This document is

If you are running Windows 3.x click File and click Exit Windows to get to an MS-DOS prompt. Double-Check Connections: Check over the connections you just made to ensure that they are correct.