Was the opening of Rogue One designed to make you think this? You can not post a blank message. Any IP addresses you see before the router's IP, listed as #2 in the tracert results in my example, is a piece of network hardware sitting between your computer and the As an aside, the Catalyst Express and 500 series switches do not have the provision for CLI. have a peek here
Advertisement Recent Posts Laptop won't boot up managed replied Feb 9, 2017 at 8:49 PM Confused & Requesting Help Macboatmaster replied Feb 9, 2017 at 8:36 PM Windows 10 upgrade- Mouse It baffles me that they were even deployed as I found enough existing cat5 drops to eliminate them all. I'll give SuperScan a try when I get into work in the morning, fingers crossed! Email Reset Password Cancel Need to recover your Spiceworks IT Desktop password?
I will definitely give this a shot.Jon Like Show 0 Likes(0) Actions Re: Finding unmanaged Switches and Hubs on the LAN email@example.com Apr 15, 2014 11:19 AM (in response to Goliath) Or perhaps suggestions on where to start? 6 commentsshareall 6 commentssorted by: besttopnewcontroversialoldrandomq&alive (beta)[–][deleted] 5 points6 points7 points 3 years ago(2 children)One unreliable method would be to look at CAM tables and list all This leaves two options I can think of. 1) The original sysadmin didn't change the ip from the default (which I think makes this impossible) 2) The original sysadmin, for reasons How To Find The Ip Address Of The Switch You Are Connected To Show 6 replies Re: Finding unmanaged Switches and Hubs on the LAN adrou Apr 17, 2013 2:03 PM (in response to irishjd) Unfortunately an unmanaged switch is unmanaged, and somehow transparent.The
Is highlighting important reference a good idea? Will an old film camera still work even when not used in a very long time? Do not expressly advertise your product. http://forums.whirlpool.net.au/archive/696517 Style Default Style Contact Us Help Home Top RSS Terms and Rules Copyright © TechGuy, Inc.
share|improve this answer answered Jun 17 '14 at 16:20 LawrenceC 48.4k677151 +1, This is the answer they were probably looking for. How To Find Switch Ip Address Cisco Like Show 0 Likes(0) Actions Re: Finding unmanaged Switches and Hubs on the LAN superfly99 Apr 18, 2013 2:02 AM (in response to irishjd) I'm guessing the issue they cause are Article A brief explanation of the 192.168.1.4 IP address Article How to Find Your PC's Private IP Address in Windows 7 Article What is an IP Address & What Are the The switch is initialized through the GUI Device Manager; no console cable or terminal emulation application is needed.
For some reason I just can't find the GS716T in the list, and therefore can't access the management page to set it a static IP address. navigate here I prefer to have a balance where I shut off all CDP traffic on all access ports and leave it enable on my trunk/uplink ports. Depending on your firewall's features, you may try your firewall logs as well. 1Votes Share Flag Collapse - Classic Problem by henrysteinhauer · 6 years ago In reply to How can If it's getting an automatically assigned IP address, check the DHCP server to see what address is assigned to that MAC address. How To Find Switch Ip Address On Network
Switches will: Have multiple ports Not have a collision LED Replicate traffic that comes in on one port to all other ports, on a Layer 2 basis, IF it hasn't seen So check the model number to make sure before going too much farther. 6 Poblano OP Steve9449 Jun 4, 2013 at 8:32 UTC Gary / Dave, I was Please type your message and try again. http://casualobserver.net/ip-address/find-my-network-ip.html Network scanner utility to find mac addresses HP Procurve Discovery Best Answer Poblano OP greenstarthree Aug 5, 2014 at 2:44 UTC Sounds like the "cleanest" option would be a factory reset.
Switch off = network off = sad office. Find Ip Address Of Switch I'm Connected To What should lecturer do? looked in the DHCP list (its not there so I'm assuming it was statically assigned) manually tried all the addresses in the block we use (192.168.1.1-254) The stupid 500G doesn't have
Try installing and running advanced IP scanner, which will tell you what devices are connected to the interfaces along with the IP address. To enable remote management of the switch through a Web browser or SNMP, you must connect the switch to the network and configure it with network information (an IP address, subnet Any advice on determining the IP address on these switches would be greatly appreciated. this contact form I would recommend using the Trace Route command: tracerthttp://support.microsoft.com/kb/314868 0Votes Share Flag Collapse - Firewall logs?
zx10guy, Jul 2, 2010 #9 zx10guy Trusted Advisor Joined: Mar 30, 2008 Messages: 4,955 Squashman said: ↑ So is it web based or is there an application that runs on a The biggest driver is a mandate from management to remove all unmanaged network devices from the network. For example, you'll certainly need to know the private IP address for your router and, if you use them on your network, the IP addresses for your switches, access points, bridges, Good times.....thanks again for all your thoughts, I'll keep you updated as I figure out more.
Which you could also scan for. It will prevent hosts getting moved around without the IT department's knowledge, and if additional hosts get plugged in you'll know where and when. If I didn't see a lease or reservation (which I wouldn't expect to see), I would then use the scan tools for the reserved range of IPs in the DHCP scope. Because the information isn't encrypted nor does it require authentication, all the information about the switch is in clear text.
Log in or Sign up Tech Support Guy Home Forums > Internet & Networking > Networking > Computer problem? You could try setting a second IP in that range on a computer at that location, but it might require a second NIC. 0 Poblano OP Steve9449 Jun You should be able to do a basic scan and determine the IP from the MAC address. 2 Serrano OP StevO93 Aug 5, 2014 at 12:17 UTC +1 How to survive in academia?
How can you recognize that blackbox as hub, switch, router or gateway without using any additional device or host? About Advertising Privacy Terms Help Sitemap × Join millions of IT pros like you Log in to Spiceworks Reset community password Agree to Terms of Service Connect with Or Sign up